After a hard rain, the middle of every slope is doing its job — shingles overlapping like scales, shedding water down to the gutters. Now look at the joints: where the roof runs into the chimney, where it meets the upstairs wall, where a vent pipe pokes through, where two slopes join in a valley. Every joint is a gap, and shingles alone cannot close a gap. That is what flashing is for: thin strips of metal, bent to fit the joint, carrying water over it and back onto the shingles below. It is the least glamorous part of a roof — and the one that causes the most leaks.
What flashing is, and where it lives
Flashing is sheet metal — usually aluminum, galvanized steel, or copper — cut and folded to fit a joint. A typical house has five kinds. Step flashing is a row of small L-shaped pieces layered in with the shingles wherever a roof meets a wall, each piece overlapping the one below it. Chimney flashing wraps the base of the chimney, with a counter-flashing set into the mortar joints. Valley flashing is a metal channel down the inside corner where two slopes meet. Vent pipe flashing is a flat base with a rubber collar — a boot — sealing around the pipe. And drip edge runs along the eaves, steering water into the gutters instead of behind them.
None of this is visible from the street the way shingles are.
Why it fails
Flashing fails for four reasons. The first is age: the sealant that beds it dries out and cracks after ten to fifteen years, and the rubber boots around vent pipes go brittle in the sun and split — a cracked vent boot is the single most common leak source on roofs under fifteen years old. The second is rust: galvanized steel eventually rusts through, especially in valleys where water sits. The third is movement — houses settle, wood swells and shrinks, chimney mortar cracks, and flashing set into a mortar joint works loose a fraction of an inch at a time. The fourth is a bad install: flashing buried under shingles in the wrong order, step flashing skipped where the roof meets a wall, a joint sealed with caulk instead of metal. Caulk is not flashing. It holds for a season, then cracks, and traps water underneath.
The signs your flashing is the problem
Flashing leaks have a tell: they show up near the joint, not in the middle of a room. Watch for a ceiling stain directly below a chimney, a skylight, or the wall where an upper storey meets the roof. Watch for a leak that appears only in wind-driven rain and then dries up — water blown under a lifted edge, not through the field of shingles. Rust streaks running down from a chimney or along a valley are a direct read, as are chunks of dried sealant in the gutters, shingles curling next to a wall or chimney, and daylight visible in the attic around a pipe or chimney. If you see any of these, the problem is almost certainly at a joint.
What a fix costs
Ballpark figures — every roof differs. Resealing a vent boot or a small joint usually runs $150 to $400. Replacing a vent pipe boot runs $200 to $500. Re-flashing a chimney runs $500 to $1,500. Re-flashing a valley runs $800 to $2,000 depending on its length, and a full re-flash around a skylight runs $500 to $1,000.
Now compare that with what a flashing leak costs left alone. Water running behind flashing soaks the roof decking and the framing around the joint, out of sight — in the attic, inside the wall. By the time a stain appears on a ceiling, the wood underneath has often been wet for months. A $300 flashing fix becomes a $3,000 to $5,000 repair once the decking and framing around it have rotted. The cheapest repair on a roof, and the most expensive one to postpone.
What not to do
Do not smear caulk or roofing tar over the joint and call it fixed. It cracks, traps water underneath, and makes the real fix harder because the next roofer has to scrape it all off first. Do not ignore a small stain because the leak "stopped" — water does not stop, it finds a new path, usually deeper into the framing. And do not let anyone pressure-wash around flashing: it drives water straight under the metal and strips the sealant holding it.
See your roof the way a roofer does — free.
Start with a free aerial exam of your roof: a full look at every slope, with a plain-English report of what is damaged and what it will take to fix it. If it needs a closer look, book a free in-person inspection — schedule online at Tryroofrover.com.
Get My Free Aerial Exam →The bottom line
Your shingles get all the attention, but your flashing does the hard work — guarding every joint where water actually wants in. Most leaks are a flashing problem, most flashing problems are cheap to fix, and the only expensive version is the one left alone. If you have a stain near a chimney or a wall, start at the joints. That is where the water is getting in.